View IRS210614S_1581132.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

june 12, 2008 IRS210614S high and low side driver ic features ? floating channel designed for bootstrap operation ? fully operational to +600 v ? tolerant to negative transient voltage, dv/dt immune ? gate drive supply range from 10 v to 20 v ? undervoltage lockout for both channels ? 3.3 v, 5 v, and 15 v input logic compatible ? matched propagation delay for both channels ? logic and power ground +/- 5 v offset ? lower di/dt gate driver for better noise immunity ? outputs in phase with inputs ? rohs compliant typical connection diagram product summary topology half-bridge v offset 600 v v out 10 v-20 v i o+ & i o- (typical) 290 ma & 600 ma ton & toff (typical) 165 ns & 165 ns package types so14n www.irf.com ? 2008 international rectifier 1 up to 600 v to load v cc v b v s ho lo com hin v ss lin v cc v ss lin hin note: please refer to page 10 for the correct pin configurat ion. this diagram shows elec trical connections only. please refer to our applicat ion notes and design tips for proper circuit board layout.
IRS210614S www.irf.com ? 2008 international rectifier 2 preliminary table of contents page description 3 qualification information 4 absolute maximum ratings 5 recommended operating conditions 6 static electrical characteristics 7 dynamic electrical characteristics 7 functional block diagram 8 input/output pin equivalent circuit diagram 9 lead definitions 10 lead assignments 10 waveform definitions 11 package details 12 tape and reel details 13 part marking information 14 ordering information 15
IRS210614S www.irf.com ? 2008 international rectifier 3 preliminary description the irs21064s is a high voltage, high speed power mosfet and igbt driver with independent high and low-side referenced output channels. proprietary hvic and latch immune cmos technologies enable ruggedized monolithic construction. the logic input is compatible with standard cmos or lsttl output, down to 3.3 v logic. the output drivers feature a high pulse current buffer stage designed for minimum driver cross-conducti on. the floating channel can be used to drive an n-channel power mosfet or igbt in the high side configuration which operates up to 600 v.
IRS210614S www.irf.com ? 2008 international rectifier 4 preliminary qualification information ? industrial ?? qualification level comments: this family of ics has passed jedec?s industrial qualification. ir?s consumer qualification level is granted by extension of the higher industrial level. moisture sensitivity level soic14n msl2 ??? (per ipc/jedec j-std-020) machine model class b (per jedec standard eia/jesd22-a115) esd human body model class 2 (per eia/jedec standard jesd22-a114) ic latch-up test class 1, level a (per jesd78) rohs compliant yes ? qualification standards can be found at international rectifier?s web site http://www.irf.com/ ?? higher qualification ratings may be available sh ould the user have such requirements. please contact your international rectifier sale s representative for further information. ??? higher msl ratings may be available for the sp ecific package types listed here. please contact your international rectifier sales re presentative for further information.
IRS210614S www.irf.com ? 2008 international rectifier 5 preliminary absolute maximum ratings absolute maximum ratings indicate sustained limit s beyond which damage to the device may occur. all voltage parameters are absolute voltages referenced to com, all currents are defined positive into any lead. the thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. symbol definition min. max. units v b high-side floating supply absolute voltage -0.3 625 v s high-side floating supply offset voltage v b - 25 v b + 0.3 v ho high-side floating output voltage v s - 0.3 v b + 0.3 v cc low-side output voltage -0.3 25 v lo low-side and logic fixed supply voltage -0.3 v cc + 0.3 v in logic input voltage v s -0.3 v cc + 0.3 v v ss logic ground v cc -25 v cc + 0.3 v/ns dv s /dt allowable offset supply voltage transient --- 50 p d package power dissipation @ t a +25 oc --- 1.0 w r thja thermal resistance, junction to ambient --- 120 oc/w t j junction temperature --- 150 t s storage temperature -50 150 t l lead temperature (soldering, 10 seconds) --- 300 oc
IRS210614S www.irf.com ? 2008 international rectifier 6 preliminary recommended operating conditions the input/output logic timing diagram is shown in fig. 1. for proper operat ion the device should be used within the recommended conditions. the v s and v ss offset rating are tested with all supplies biased at a 15 v differential.. symbol definition min. max. units v b high-side floating supply absolute voltage v s + 10 v s + 20 v s high-side floating supply offset voltage note 1 600 v ho high-side floating output voltage v s v b v cc low-side output voltage 10 v lo low-side and logic fixed supply voltage 0 v cc v in logic input voltage v ss v cc v ss logic ground -5 5 v t a ambient temperature -40 125 oc logic operational for vs of -5 v to +600 v. logic state held for vs of -5 v to -vbs. (please refer to the design tip dt97-3 for more details). ?
IRS210614S www.irf.com ? 2008 international rectifier 7 preliminary static electrical characteristics v bias (v cc , v bs ) = 14 v, c t = 1 nf and t a = 25 c unless otherwise specified. the v o and i o parameters are referenced to com and are applicable to the respective output leads: ho or lo. clo1=clo2=cho1=cho2=1 nf. symbol definition min typ max units test conditions low voltage supply characteristics v ih logic ?1? input voltage 2.5 ? ? v il logic ?0? input voltage ? ? 0.8 v v cc = 10 v to 20v v oh high level output voltage, v bias -v o ? 0.05 0.2 v ol low level output voltage, v o ? 0.02 0.1 i o = 2 ma i lk offset supply leakage current ? ? 50 v b = v s = 600 v i qbs quiescent vbs supply current 20 75 130 i qcc quiescent vcc supply current 60 120 180 v in = 0 v or 5v i in+ logic ?1? input bias current vin = 5 v ? 5 20 i in- logic ?0? input bias current vin = 0 v ? ? 5 a v ccuv+ v bsuv v cc and v bs supply undervoltage positive going threshold 8.0 8.9 9.8 v ccuv- v bsuv- v cc and v bs supply undervoltage negative going threshold 7.4 8.2 9.0 v ccuvh v bsuvh hysteresis 0.3 0.7 ? v i o+ output high short circuit pulsed current 130 290 ? vo = 0 v, pw 10 s i o- output low short circuit pulsed current 270 600 ? ma vo = 15 v, pw 10 s dynamic electrical characteristics v bias (v cc , v bs ) = 15 v, v ss = com, c l = 1000 pf, t a = 25 c. symbol component min. typ. max. units test conditions t on turn-on propagation delay --- 165 230 v s = 0 v t off turn-off propagation delay --- 165 230 v s = 0 v or 600 v mt delay matching, hs & ls turn-on/off --- 0 30 t r turn-on rise time --- 100 220 t f turn-off fall time --- 35 80 ns v s = 0 v
IRS210614S www.irf.com ? 2008 international rectifier 8 preliminary functional block diagram irs21064 lin uv detect delay com lo vcc hin vss vs ho vb pulse filter hv level shifter r r s q uv detect pulse generator vss/com level shift vss/com level shift irs210614
IRS210614S www.irf.com ? 2008 international rectifier 9 preliminary i/o pin equivalent circuit diagrams
IRS210614S www.irf.com ? 2008 international rectifier 10 preliminary lead definitions pin# symbol description 1 v cc low-side and logic fixed supply 2 hin logic input for high-side gate driver output (ho), in phase 3 lin logic input for low-side gate driver output (lo), in phase 4 nc no connect 5 v ss logic ground 6 com low-side return 7 lo low-side drive output 8 nc no connect 9 nc no connect 10 nc no connect 11 v s high-side floating supply return 12 ho high-side gate drive output 13 v b high-side floating supply 14 nc no connect lead assignments 14 13 12 v b 1 v s ho com 4 5 7 6 2 3 lo v ss 11 10 9 8 nc nc nc nc nc v cc hin lin
IRS210614S www.irf.com ? 2008 international rectifier 11 preliminary waveform definitions
IRS210614S www.irf.com ? 2008 international rectifier 12 preliminary package details: so14n
IRS210614S www.irf.com ? 2008 international rectifier 13 preliminary package details: soic14n, tape and reel carrier tape dimension for 14soicn code min max min max a 7.90 8.10 0.311 0.318 b 3.90 4.10 0.153 0.161 c 15.70 16.30 0.618 0.641 d 7.40 7.60 0.291 0.299 e 6.40 6.60 0.252 0.260 f 9.40 9.60 0.370 0.378 g 1.50 n/a 0.059 n/a h 1.50 1.60 0.059 0.062 metric imperial reel dimensions for 14soicn code min max min max a 329.60 330.25 12.976 13.001 b 20.95 21.45 0.824 0.844 c 12.80 13.20 0.503 0.519 d 1.95 2.45 0.767 0.096 e 98.00 102.00 3.858 4.015 f n/a 22.40 n/a 0.881 g 18.50 21.10 0.728 0.830 h 16.40 18.40 0.645 0.724 metric imperial e f a c d g a b h n ote : controlling dimension in mm loaded tape feed direction a h f e g d b c
IRS210614S www.irf.com ? 2008 international rectifier 14 preliminary part marking information
IRS210614S www.irf.com ? 2008 international rectifier 15 preliminary ordering information standard pack base part number package type form quantity complete part number tube/bulk 55 IRS210614Spbf IRS210614S soic14n tape and reel 2500 IRS210614Strpbf the information provided in this document is believed to be accu rate and reliable. however, international rectifier assumes no responsibility for the consequences of the use of this information. international rectifier assumes no responsibility for any infringement of patents or of other rights of third parties which may result from the use of this information. no license is g ranted by implication or otherwise under any patent or patent rights of inte rnational rectifier. the spec ifications mentioned in this do cument are subject to change without notice. this document supersedes an d replaces all information previously supplied. for technical support, please contact ir?s technical assistance center http://www.irf.com/technical-info/ world headquarters : 233 kansas st., el segundo, california 90245 tel: (310) 252-7105

▲Up To Search▲

Price & Availability of IRS210614S

	To Download IRS210614S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .